This arcade stick modding guide buttons lever artwork walkthrough covers the three mods most players start with: swapping buttons, changing the lever, and fitting custom art. You do not need a workshop or soldering skills for most of it. You need the right parts for your stick, a few basic tools, and the patience to test each change before moving to the next.
This arcade stick modding guide buttons lever artwork approach works best one mod at a time: arcade stick modding for beginners should start with buttons. Change the buttons, play for a week, and decide what you actually want next. Changing everything at once makes it hard to tell which part improved the feel and which part made it worse.
Arcade Stick Modding Guide Buttons Lever Artwork: Know Your Stick First
Before this arcade stick modding guide buttons lever artwork project goes further, open the case and look before you order anything. Note the button size, usually 30mm for action buttons and 24mm for start and select, the lever brand and mounting plate, and whether the wiring uses quick-disconnect terminals or a harness. Take a photo of the wiring before you touch it, so you can put it back exactly as it was.
- Check the button sizes and the connector type inside your stick.
- Note the lever model and whether it uses a square, octagonal, or circular gate.
- Photograph the wiring layout before disconnecting anything.
- Keep the original parts in a labelled bag in case you want to reverse a mod.
Compatibility is the main trap in any arcade stick modding guide buttons lever artwork project. Parts made for one stick do not always fit another, and a lever with the wrong mounting plate will not sit flat. Buy parts listed for your exact stick model, or check the measurements against the parts already inside it.
fight pads, arcade sticks and leverless controllers compared
How to Swap Arcade Stick Buttons
In this arcade stick modding guide buttons lever artwork walkthrough, learning how to swap arcade stick buttons is the best first mod. Open the case, pull the quick-disconnect terminals off the old button’s tabs, press the button tabs on the underside to release it, and push the new button in from the top until it clicks into place. Push the terminals back onto the matching tabs, matching the wire colours to your photo.
Work one button at a time so the wiring stays in order, and keep the arcade stick modding guide buttons lever artwork photo you took handy. After each button, test it in a game or in the console’s controller test screen before closing the case. A terminal that looks connected but sits loose will give you a button that works sometimes and fails in the middle of a match.
| Part | Difficulty | Tools needed |
|---|---|---|
| Buttons | Easy, first mod | Small flat screwdriver |
| Lever | Medium | Screwdriver, spanner for the ball top |
| Gate | Easy | Screwdriver |
| Artwork | Medium | Template, cutter, plexi layer |
Arcade Stick Lever Replacement
In an arcade stick modding guide buttons lever artwork plan, an arcade stick lever replacement changes how the stick feels more than any other single part. The lever is the assembly under the ball top: the shaft, the spring, the pivot, and the switches that register directions. Swapping the whole lever is straightforward, but the mounting plate and the wiring harness must match your case.
To swap it, remove the ball top, undo the mounting screws, and lift the lever out. Note how the harness plugs in, then fit the new lever in the same orientation and fasten it down. Test every direction before you close the case: up, down, left, right, and the diagonals. A lever fitted upside down will read the wrong directions.
The gate matters too. A square gate gives distinct corners for charge moves, an octagonal gate gives a smoother circular feel, and a circular gate suits players who ride the edge. The gate is a cheap part and easy to swap, so try it before buying a whole new lever.
Sanwa Buttons Upgrade Arcade Stick: Is It Worth It?
In this arcade stick modding guide buttons lever artwork, a Sanwa buttons upgrade arcade stick mod is the most common recommendation, and for good reason: Sanwa buttons are the standard in many arcade cabinets, with a light, responsive press and a consistent feel across all eight buttons. If your stock buttons feel mushy or uneven, this is the fix.
That said, the stock buttons on a good stick are already decent. If you like the feel of your current buttons, spend the money on a lever or a gate first. The best mod is the one that fixes a problem you actually feel, not the one everyone else recommends.
Custom Arcade Stick Artwork: How to Do It Well
Custom arcade stick artwork turns a stock stick into yours, and it is the part of this arcade stick modding guide buttons lever artwork people notice first. Start with a template made for your exact stick model, design or print at the right size, and cut the button holes cleanly. A rough cut around a button hole will catch the eye every time you look down.
Protect the print with a clear plexi or acrylic layer made for your stick. It stops the art from wearing where your palms rest and keeps spills off the paper. Lay the art flat, fit the plexi over it, and fasten the panel evenly so the art does not bunch at one side.
when to repair a controller yourself and when to stop
Arcade Stick Modding Guide Buttons Lever Artwork: Frequently Asked Questions
Is arcade stick modding hard for a beginner? Button swaps are the easiest first mod: most buttons use quick-disconnect terminals that pull off and push on. Lever swaps need a little more care with the mounting plate and wiring, while artwork swaps need patience with measuring and cutting. Start with buttons, then move on.
Do I need to solder to mod an arcade stick? Usually not. Most modern sticks use quick-disconnect terminals for buttons and a wiring harness for the lever, so swaps are plug-and-play. Older or heavily customised sticks may have soldered joints, so check inside your stick before ordering parts.
Will new buttons make me better at fighting games? They can make inputs feel more consistent, which helps execution, but they will not replace practice. The real gain is comfort and reliability: buttons that respond the same way every time let you trust your hands.
Can I put custom artwork on any arcade stick? Most sticks with a removable top panel accept printed artwork, but the size and screw layout differ by model. Measure your panel or buy a template made for your exact stick, and use a clear plexi layer to protect the print.
One mod at a time, test as you go, and keep the original parts. That is the whole method in this arcade stick modding guide buttons lever artwork.
Still choosing between stick types? Read our Fight Pads, Arcade Sticks & Leverless Controllers: Which Fighting-Game Controller Fits You.

